|
| |
 |
7030000 Diaphragm Valve,
for thin materials, for use in full automation. See below for thicker
materials. The
7030000
low viscosity auto diaphragm
valve (left) is ideal
for thin materials, such as
Cyanoacrylates
and other low to medium viscosity fluids
using a diaphragm
design.
For a typical valve
setup,
click here.
|
|
In this Category:
MOD Diaphragm
AMD Diaphragm
Auto Diaphragm
Dual Acting
Other Valves
You may also be
interested in:
Dispensers
Valve Controller
Dispense Valves
Reservoirs
Robot
Platform
Also of interest;
Precision Needles
Needle Nozzles
Thin Wall tips
Dispensing
Help
Doming & Potting
Solder Dispensing
Solder Mask |
|
To feed any IDS valve,
choose from our dispensing syringes, (to
feed thin to medium materials in very small shots) our
single cartridges, (for medium
to thicker materials in smaller shots or beads) or for large volume
capacity, order one of our
reservoirs (for thin to medium materials) or one of our
pail dispenser units, for thicker
materials. This dispensing
valve utilizes only
one moving part and requires minimal maintenance. Fluctuating air
pressure
from the controller and
material pressure above and below the diaphragm
cause the disk to float up and down to start and
stop the dispense cycle. The wetted part is the easy-to-replace diaphragm which allows material to pass through without touching the
metal chamber. For
use with
Cyanoacrylates, reagents, alcohol, paints, inks, UV adhesives, solvents, glues,
electrolytes of varying thickness.
7030000 Diaphragm Valve
Ordering
7030000
Automation
air actuated valve - non SS
7030000SP
Automation
air actuated valve - Spare Parts Kit
|
|
|
 |
The
7040000-3
valve is
an all plastic dispense valve designed for CA's and Anaerobics but can
be used with any other unfilled single part materials and is UV safe.
The rigid diaphragm design allows the
7040000-3
to
accurately dispense fluids more like a front closing valve and can be
used to dispense fine lines or smaller repeatable dots.
Click on the picture, left, for a larger image. |
|
The
7040000-3 is an all plastic dispense valve that uses a unique
rigid diaphragm design to act as a front
closing valve to accurately dispense small dots and fine beads. This
valve can be used in handheld applications, mounted on a fixture for
hands free dispensing, or mounted to a robot for automated dispensing.
The plastic construction allows adhesives such as
Cyanoacrylates and
Anaerobics to be dispensed through the valve along with a variety of
other low to high viscosity fluids. Applications include dispensing
dots, beads, potting.
The
7040000-3 has a divorced design comprising of two major sections,
the top, or Air section (Aluminum top portion)
which is an aluminum body with a simple piston/cylinder
combination used to open and close the valve.
A stroke adjustment bolt in the upper air body controls how far the
piston and needle assembly can retract thus regulating the rate of fluid
flow. The second section is the
Fluid section (Delrin body with Teflon diaphragm)
which is made up of a Delrin with a rigid Teflon diaphragm
connected to the air piston. Fluid
dispenses as the point of the diaphragm is lifted out of the fluid
section orifice then stops as it moves back into place. The stroke
adjustment bolt of the air cylinder regulates the distance that the
diaphragm tip can lift out of the fluid section orifice thus controlling
rate of fluid flow.
Controller. |
|
7040000-3
Diaphragm Valve Ordering
7040000-3
All plastic dispense
valve
7040000-3SP
All plastic dispense valve
- Spare Parts Kit
|
| |
|
